VAN NUYS, CA, USA
N58126
Bell 205A-1
During a night training flight over mountainous terrain the pilot heard a loud 'clunking' sound, which was accompanied by vibrations. The engine then emitted a loud grinding, metallic grating sound. Simultaneously, warning lights, engine chip lights, and the rpm decay light became illuminated. The pilot lowered the collective and entered an autorotation but did not have sufficient airspeed and altitude to reach a dirt road, so he turned down a canyon and performed a hard flare and near-vertical descent with little forward speed. The helicopter landed hard and came to rest on rough uneven terrain surrounded by trees and high vegetation. Postaccident examination revealed that the engine power turbine as viewed from the exhaust exhibited damage. The number 4 turbine wheel was missing all of its blades and the blades on the number 3 turbine wheel were damaged. Scoring was evidenced on the inside diameter of the turbine case in the area of the Nos. 3 and 4 turbine wheels. All the vanes and inner and outer supports of the second stage power turbine nozzle were displaced and/or missing, and fragments of the outer vane support were torn and distorted. The third stage turbine nozzle exhibited extensive damage on the trailing edges of the vanes and on the shroud/outer housing. Metallurgical examination of the turbine components disclosed features indicative of overload fractures without evidence of material defects or fatigue. The metallurgist concluded that the overall type and degree of engine damage was indicative of a component failure in the second stage power turbine nozzle area; however, the cause of the component failure was not determined.
On January 2, 1999, at 2115 hours Pacific standard time, a Bell 205A-1, N58126, landed hard during a autorotation in Rustic Canyon, about 7 miles southwest of the Van Nuys, California, airport. The forced landing was precipitated by a loss of engine power during a climb following takeoff. The aircraft sustained substantial damage. The commercial pilot and one crewmember were not injured. The other crewmember sustained serious injuries. The public-use helicopter was being operated by the Los Angeles City Fire Department as a training flight at the time of the accident. The flight originated at the Van Nuys Airport about 2000, and a company visual flight rules (VFR) flight plan was on file. Night visual meteorological conditions prevailed. The pilot reported that the purpose of the flight was to practice "Night-Sun" operations. After 1 hour of training the pilot landed the helicopter on a dirt road so the crewmembers could switch seats. He reported that after conducting a crew briefing, he lifted off and began a climb to the north. The pilot stated that approximately 10 to 15 seconds later, and about 75 feet agl, he initiated a left turn to the west. He reported that almost immediately after beginning the turn he heard a loud "clunking" sound, which was accompanied by vibrations. The engine then emitted a loud grinding, metallic grating sound. Simultaneously, warning lights, engine chip lights, and the rpm decay light became illuminated. The pilot reported that he immediately lowered the collective and entered an autorotation. He stated that he did not have sufficient airspeed and altitude to reach the dirt road, so he started a 180-degree left turn down the canyon. He informed the crew that they had an engine failure and would be going to the bottom of the canyon. The pilot reported that after reaching treetop level, he performed a hard flare and near-vertical descent with little forward speed. The helicopter landed hard and came to rest on rough uneven terrain surrounded by trees and high vegetation. The pilot reported that after egress of the aircraft, he did not smell or see smoke, nor did he note any fuel leakage. He further stated that the engine and rotor blades were stopped. The pilot reported that he had not experienced any mechanical abnormalities with the aircraft prior to the onset of the engine problem. The helicopter was recovered from the site with a hoist assembly and was examined on January 7, 1999 by the Safety Board with technical assistance from Bell Helicopters and Allied Signal. Examination of the airframe revealed that the main cabin assembly was intact. The belly of the aircraft exhibited dents and crushing damage. The cockpit area and flight controls appeared undamaged. The pilot's seat appeared to be bent downward approximately 1 inch at the forward edge. The copilot's seat appeared undamaged. The main rotor mast and controls had been removed from the transmission. The transmission was still mounted to the airframe and it was noted that the transmission input quill rotated freely in the freewheel direction (counter-clockwise) but would not rotate in the drive direction. The main driveshaft was intact. The tailboom was intact but had been removed from the fuselage. The upper right tailboom attachment fitting displayed a fracture; the fractured portion remained attached to the tailboom assembly. A portion of the fuselage mounted tailboom attachment fitting was present at the upper right-side corner of the forward bulkhead of the tailboom. The right-side synchronized elevator assembly was damaged and had been pushed aft in the tailboom structure. The tail rotor assembly was still mounted to the top of the vertical fin. Drive and control continuity was established from the fuselage aft to the tail rotor assembly. One tail rotor blade exhibited a cut approximately 1/16 inch wide and 3/4 inch deep in the leading edge. The engine was still attached to the airframe. Both legs of the engine mount bipod on the right side of the engine were bent aft. The forward and inner legs of the engine mount were also bent. The engine controls and accessories remained intact. The engine power turbine as viewed from the exhaust exhibited damage. The number 4 turbine wheel was missing all of its blades and the blades on the number 3 turbine wheel were damaged. Scoring was evidenced on the inside diameter of the turbine case in the area of the Nos. 3 and 4 turbine wheels. The engine was removed from the airframe and shipped to Allied Signal Corporation for further testing. The engine was examined on January 25 and 26, 1999, under the supervision of the Safety Board. Disassembly of the engine revealed that all the vanes and inner and outer supports of the second stage power turbine nozzle were displaced and/or missing, and fragments of the outer vane support were torn and distorted. The third stage turbine nozzle exhibited extensive damage on the trailing edges of the vanes and on the shroud/outer housing. The Allied Signal metallurgist reported that this damage was indicative of secondary damage resulting from the separations of the third stage blades and the fourth stage nozzle. Almost all of the fourth stage turbine nozzle was missing, except for portions of the outer band. The metallurgist was not able to determine the exact cause of the damage; however, he noted that the remaining features on the fourth stage nozzle were indicative of an overload fracture mode. He further concluded that the separations of the blades on both the third and fourth stage turbine wheel assemblies were indicative of an overload fracture mode. No material defects or fatigue cracks were observed on the overload fractures. The metallurgist concluded that the overall type and degree of engine damage was indicative of a component failure in the second stage power turbine nozzle area; however, the cause of the component failure was not determined. All other damage observed was concluded to be secondary.
A loss of engine power due to an undetermined component failure in the second stage power turbine nozzle area. Factors in the accident were the mountainous/hilly nature of the terrain and the dark night lighting conditions which precluded the pilot from selecting a suitable forced landing area.
Source: NTSB Aviation Accident Database
Aviation Accidents App
In-Depth Access to Aviation Accident Reports
