Aviation Accident Summaries

Aviation Accident Summary LAX99FA200

HUNTINGTON BCH, CA, USA

Aircraft #1

N811CE

MBB BO 105LS A-3

Analysis

The purpose of the flight was to transport two company employees to an island located 22 miles offshore. The pilot was not instrument rated. The weather conditions along the coast consisted of overcast skies with cloud bases from 700 to 1,100 feet, and, tops between 1,900 and 2,200 feet; visibilities were generally in the 4- to 5-mile range. Ground and pilot witnesses said that a localized area of lower cloud bases, between 350 and 500 feet, and reduced visibilities of about 1.5 miles existed in the area of the accident site. Review of recorded radar data disclosed that the helicopter descended from a cruise altitude of 900 feet and crossed the shoreline at 400 feet. As the helicopter reached the accident site location, it climbed to 600 feet over 19 seconds, then turned right to a northerly heading while the altitude climbed from 600 to 900 feet; the radius of turn was calculated at 720 feet at an average ground speed of 69 knots. The helicopter then descended to 700 feet as the radar track began a wide left turn, which then reversed to a tight right turn. The last four radar returns showed a right turn with a 120-foot radius, with a constant Mode C report of 700 feet; the average computed ground speed during this turn was 67 knots. The last radar return was a secondary beacon without a Mode C altitude report; the location of the last radar return was about 200 feet from where the wreckage was found on the ocean floor. No preimpact mechanical malfunctions or failures were found during examination of the wreckage.

Factual Information

HISTORY OF FLIGHT On May 28, 1999, about 0648 hours Pacific daylight time, a Messerschmitt-Bolkow-Blohm (MBB) BO 105LS A-3 helicopter, N811CE, crashed into the Pacific Ocean approximately 6 miles west-southwest of the Huntington Beach Pier, Huntington Beach, California. The aircraft, operated by Southern California Edison, Ontario, California, was destroyed. The commercial pilot was not recovered and is presumed to have sustained fatal injuries; the two passengers were recovered with the wreckage and suffered fatal injuries in the accident. The flight was conducted under the provisions of 14 CFR Part 91 as a corporate flight to transport two Edison employees to Catalina Island. The flight originated at an Edison Service Center helipad near Irvine, California, about 0625 as a non-stop flight to the Pebbly Beach helipad on Catalina Island, which is about 25 miles offshore. Visual meteorological conditions prevailed at John Wayne airport, near Irvine, at the time of the accident. No flight plan was filed with the Federal Aviation Administration (FAA); however, company flight following was being provided to the pilot. FAA facility records disclosed that no ATC services or weather briefings were provided to the pilot on the morning of the accident. In both an oral interview and a written statement, the Chief Pilot for the company stated that prior to departure the pilot telephoned the company stations at Rosemead, San Onofre, Irvine, and Westminster for en route weather conditions. The company employee stationed at Catalina Island who was to pickup the passengers said the pilot did not contact him for the weather conditions. According to weather reports and witness observations from pilots flying along the same general route, the weather in the channel between the Southern California coast and Catalina Island included cloud bases between 500 and 700 feet, and visibility values ranging from 1 to 3 miles. Isolated areas of lower cloud bases and visibility values were observed by the witnesses. According to Southern California Edison, the pilot departed the Ontario airport at 0521, and flew to the company's general offices in Rosemead and picked up one of the passengers. The pilot had intended to fly to a company helipad in San Onofre to pickup the other passenger; however, the weather along the coast in the San Onofre area included fog and limited visibility. The pilot then asked the second passenger to drive to the Irvine helipad. The flight then left Rosemead and arrived at the Irvine helipad at 0610. After picking up the passenger, the flight departed for Santa Catalina Island. At 0640, the pilot talked to another company pilot on the radio and stated he would be "feet wet in 2 minutes." No further communications were recorded from the helicopter. According to the company chief pilot, the pilot had stated the night before that he intended to cross the coast at the Huntington Beach Pier and proceed direct across the channel to the island. When the helicopter failed to arrive at Catalina, the company reported it missing and search efforts were initiated by the U.S. Coast Guard. Debris identified from the helicopter was found floating about 3.5 miles off the pier at 1203, along with a fuel slick. The Coast Guard reported the location of the debris field as north latitude 33 degrees 37.2 minutes by west longitude 117 degrees 58.2 minutes. Recorded radar data covering the area of the accident was examined for the time frame, and a 1200 secondary beacon code target was observed that matched the anticipated flight track of the helicopter from the Irvine helipad to the point of disappearance. The data was supplied by the FAA in the form of a National Track Analysis Program (NTAP) printout from the Los Angeles Air Route Traffic Control Center (ARTCC) long range search radar at San Pedro, California, and a ARTS-IIIA CDR Editor listing from the Southern California Terminal Radar Approach Control, Los Alamitos, California, terminal radar antenna site. The data was then processed in the computer program Radar Viewpoint, by Airways Technology, Inc. Review of the processed and raw data disclosed that the target was first identified at 0629:16 as it tracked northwest bound over the Interstate 5 freeway from the Irvine area climbing from a Mode C reported altitude of 500 feet to 900 feet. Shortly after reaching 900 feet, it then descended again to 600 feet. At 0636:50, the target turned southbound and tracked over the Santa Ana River until crossing the shoreline near the Huntington Beach pier at 0643:24. The Mode C reported altitude descended to 400 feet as the target crossed the shoreline. Beginning at 0646:24, the Mode C reported altitude climbed to 600 feet over 19 seconds, then turned right at 0646:47 to a northerly heading while the Mode C altitude exhibited a climb from 600 to 900 feet; the computer program calculated the radius of turn at 720 feet at an average ground speed of 69 knots. The Mode C reports then descended to 700 feet as the track began a wide left turn, which reversed to a tight right turn. The last four beacon returns showed a right turn with a 120-foot radius with a constant Mode C report of 700 feet; the average computed ground speed during this turn was 67 knots. The last radar return was a secondary beacon without Mode C at 0648:12, about 6 miles west south west of the Huntington Beach pier at west longitude 118 degrees 05 minutes 58 seconds by north latitude 33 degrees 36 minutes 44 seconds. PERSONNEL INFORMATION During the investigation, certified copies of the pilot's records were obtained from the FAA's Aeromedical Certification Division and the Airman Certification Branch. In addition, flight department records obtained from Southern California Edison were reviewed to document the pilot's training history, flight time, and, the recent duty/rest period activity within the week prior to the accident. The pilot's FAA Airman Record file established that he held a commercial pilot certificate for rotorcraft helicopters with private privileges in single engine land airplanes. The most recent issuance of the pilot certificate was dated May 1, 1982, and was due to successfully passing the required tests for the commercial certificate in rotorcraft. The pilot did not hold an instrument rating for either rotorcraft or airplanes. In addition, he held an Airframe and Powerplant mechanics certificate and an Inspection Authorization. Review of his Aeromedical Certification Division records disclosed that he held a second-class medical certificate issued November 30, 1998. The medical certificate contained the limitations that correcting lenses be possessed for near and intermediate vision. The pilot's medical record file also revealed that on December 5, 1990, he was issued a Statement of Demonstrated Ability waiver (SODA), number 30DD9025, for deficient right eye vision beyond the standards prescribed in 14 CFR 67.203. According to the most recent medical certificate examination form (FAA Form 8500-8), the pilot's corrected right eye visual acuity was 20/200 for distant and intermediate ranges, and, 20/100 for near ranges. The corrected visual acuity in the left eye was 20/20 in all ranges. Further examination of the records disclosed that the pilot was diagnosed in October 1989 with ischemic optic neuropathy of the right eye. The issuance of the SODA by the FAA Aeromedical Certification Division was based on medical examinations and the pilot's successful completion of a practical demonstrated ability test. According to company records, the pilot had accrued a total flight time of 4,341 hours, of which 4,112 were in rotorcraft, and 49 in the BO-105. In the preceding 90 and 30 days, the pilot had flown 137 and 35 hours respectively, with 11 hours flown in the BO-105. The pilot's total night experience was determined to be 22 hours, with 2 hours flown in the past 90 days. No instrument flight experience was found in the records supplied. His most recent biennial flight review was accomplished on September 22, 1998, in an American Eurocopter AS-350 as part of a factory conducted recurrent ground and flight training session. The records also disclosed that the pilot completed the Eurocopter factory conducted ground and flight training program in the BO-105 on November 18, 1998. No deficiencies were noted on the training forms for the factory courses. The company chief pilot reported that a desktop simulator was available in the flight department offices for the use of the pilots; no record of the pilot using the device was located. Company records were examined to determine the pilot's duty and rest periods for the 7 days preceding the accident. The pilot was off duty over May 22 and 23, and reported for work at 0715 on May 24 for a 10-hour shift. He reported for a 12-hour shift at 0730 on May 25, and had a 10-hour shift beginning at 0700 on May 26. On May 27, he worked a 9-hour shift from 0900 to 1800. The pilot reported for duty at 0400 on the day of the accident. Interviews were conducted with company pilots who interacted with the pilot in the days preceding the accident. All reported that the pilot appeared healthy and upbeat. The company pilot who spoke with the pilot by radio on the day of the accident stated that he sounded normal in all respects. There was no indication from family members or other company pilots that the pilot was taking any prescription or over the counter medications. AIRCRAFT INFORMATION The maintenance records for the helicopter were obtained from the operator and reviewed. In addition, information and records were obtained from American Eurocopter concerning original equipment installed during production. The aircraft and registration files maintained at the FAA Registry in Oklahoma City, Oklahoma, were also reviewed. The BO 105LS A-3 helicopter, serial number 2036, was manufactured by MBB Helicopters Canada Limited on May 27, 1991. Between the production date and August 12, 1994, it was a MBB factory demonstrator under Canadian registration C-FSBK, and accumulated a total time of 49 hours. It was then de-registered and shipped to Japan, where it again was a demonstrator model for the MBB distributor in that country. The helicopter was sold to the present owner and arrived in the United States on October 12, 1998, with an accumulated total time of 83 hours since new. A U.S. Standard airworthiness certificate in the normal category was issued and the helicopter registered as N811CE. At the time of the accident, the airframe and both engines had accumulated a total of 233 hours, 939 landing cycles, and 510 engine cycles. The most recent 100-hour inspection was completed on March 26, 1999, 39 hours prior to the accident. A combined manufacturers 25- and 50-hour inspections were accomplished on May 11, 1999. Safety Board investigators reviewed the operator's "Daily Helicopter Flight Report" forms. The last one available was dated May 20, 1999. Two unresolved discrepancies were noted. The first, dated March 12, 1999, noted that the "DAVTRON gage stuck on voltage." The second, dated March 29, 1999, listed the 900 MHz radio as intermittent. On the morning of the accident, the operator's dispatch records showed that the helicopter departed the company's Ontario flight operations base with 110 gallons of Jet A onboard. Manufacturer's records disclosed that the helicopter was equipped with the instruments required by 14 CFR 91.207 for flight in instrument conditions; however, it was not certified for IFR flight. The dual hydraulic power pack installed on the helicopter was a p/n 105-450121, serial number 17-004. Airworthiness Directive 96-08-04 was not applicable to either the 105LS A-3 model helicopter or the hydraulic pack by part number. COMMUNICATIONS A review of radio communications from FAA sources, the frequency used by the company, and other CTAF frequencies used by helicopters in the harbor area, revealed that no distress calls were monitored during the time frame of the accident flight. METEOROLOGICAL INFORMATION A staff Safety Board meteorologist prepared a factual report of the meteorological conditions in the vicinity of the helicopter's flight route. That report is appended to this file. The 0653 aviation surface weather observation at the Santa Ana airport (close to the departure helipad) was reporting a cloud ceiling of 1,100 feet overcast, with a 5-mile surface visibility. Other coastal airports within 10 miles of the accident site were reporting overcast ceilings ranging from 700 to 1,100 feet, with visibilities between 4 and 5 miles in mist. Pilot reports for the area showed the tops of the stratus clouds ranging from 1,900 to 2,200 feet msl. A witness report from the destination helipad at Avalon on Catalina Island included an estimated 2-mile visibility in fog with cloud bases of at least 500 feet. Other helicopter pilots who fly passengers on scheduled flights for a commuter operator between the Los Angeles Harbor and Catalina stated that about 0700, the weather in the channel was 700 overcast with 3 miles, but that an area of lower fog and reduced visibility existed toward the southeast in the area offshore of the Huntington Beach Pier. Two additional witnesses were located on offshore oil platform Ellen, which is about 2.5 miles southwest of the final location of the helicopter. According to the witnesses, they were on deck during the time frame of the accident. The witnesses estimated the cloud bases on the basis of the known height of the oil rig top. Visibility estimates were made on the basis of distances to known objects and geographical features around the platform. They reported that the sky was overcast with bases estimated at 300 to 350 feet msl. The visibility varied according to the cardinal magnetic direction away from the platform and was noted by the witnesses to be: 2 to 2.5 miles to the north; 3 miles to the west; 1 to 2 miles to the south; and 1.5 to 2 miles to the east. In pertinent part, the Safety Board meteorologist noted that the area was under the influence of a low pressure centered near Needles, California, with a weak inverted trough extending northwestward through central California. High humidity and light winds were found in station plots along the California coastline. Digital brightness data obtained from the GOES-10 satellite for the time frame of the accident showed that the helicopter's radar derived ground track moved from an area with a 61 to 87 brightness count to a 88 to 255 brightness count area when radar contact was lost. The aviation area forecast for the Pacific Coast was issued by the National Weather Service at 0345 on the morning of the accident. AIRMET Sierra was contained in the area forecast and predicted IFR conditions for the Southern California Coastal waters with broken to overcast ceilings of 1,000 feet; visibilities from 3 to 5 miles in mist and tops of the stratus clouds at 2,000 to 3,000 feet. WRECKAGE AND IMPACT The wreckage was located by a side scan sonar search on June 2, 1999, on the ocean floor at a depth of 50 meters. The coordinates of the wreckage were north latitude 33 degrees 36 minutes 46 seconds by west longitude 118 degrees 05 minutes 55 seconds. Prior to any recovery attempt, the wreckage was videotaped by the salvage firm hired for the retrieval. Safety Board investigators reviewed the video footage and examined the side scan sonar image. All helicopter extremities were present in the immediate vicinity of the main wreckage mass. The tail boom was attached to the fuselage, and the tail rotor blades remained attached to the hub. While damaged, distorted, and fractured at the transition point from the grip arm to the full cord width, all four main rotor blades were attached to the hub. On June 3, 1999, divers secured a cable to the mast and the helicopter was lifted to the surface. During the process of lifting the wreckage clear of the water, one main rotor blade (subsequently identified as the red blade) separated at the fracture point and sank to the ocean floor. Beyond the one main rotor blade, the only major piece of wreckage not recovered was the pilot's cockpit

Probable Cause and Findings

The pilot's in-flight loss of control due to spatial disorientation while maneuvering to reverse direction after an inadvertent encounter with instrument meteorological conditions.

 

Source: NTSB Aviation Accident Database

Get all the details on your iPhone or iPad with:

Aviation Accidents App

In-Depth Access to Aviation Accident Reports