Arlington, WA, USA
N4029Q
Robinson R22 Beta
This was the pilot-rated student's first instructional flight in the recently rebuilt helicopter, which he purchased three days prior to the accident flight. About 5 minutes after the helicopter's departure on the accident flight, witnesses reported hearing a loud bang and watching the helicopter fall to the ground. The helicopter impacted terrain in an approximately level attitude, coming to rest in an upright position. There was no postcrash fire. All major components of the helicopter were accounted for and recovered before being moved to a secured storage facility. Both of the helicopter's doors separated from the aircraft in flight. The right door was recovered intact and not damaged, while the left door was accounted for in multiple fragmented pieces, including the door handle and frame, and the door latching mechanism. Both tail rotor blades were located 500 to 600 feet prior to the main impact point, with one blade exhibiting two large impact areas near the tip of the leading edge. One impact area was more rounded than the other, with the other impact area being broader and very flat. Examinations of paint transfers revealed that the material on the leading edge of a piece of main rotor blade and on the door latching mechanism were transferred paint from the tailboom, and that the yellow paint on the main rotor blade was similar to the paint from the tail rotor blade and likely from the same source. The sequence of events preceding the day of the accident flight, as well as the physical evidence examined during the investigation, indicates that the door pins were not installed prior to the flight. Physical evidence consistent with the helicopter's main rotor diverging from its normal plane of rotation and striking the left windscreen was observed in the form of an area of black transfer material, which measured 24 inches by 5 inches on the upper left outboard area of the left windscreen. The initiating event that produced the main rotor divergence could not be determined.
HISTORY OF FLIGHT On November 27, 2004, about 0935 Pacific standard time, a Robinson R22 Beta helicopter, N4029Q, registered to and operated by a private individual, was destroyed while maneuvering when it experienced an in flight break-up followed by impact with the terrain during an uncontrolled descent near Arlington, Washington. The flight instructor and the pilot-rated student sustained fatal injuries. Visual meteorological conditions prevailed and a flight plan was not filed for the 14 CFR Part 91 instructional flight. The local flight departed the Arlington Municipal Airport (AWO), Arlington, Washington, at approximately 0930. In a statement submitted to the National Transportation Safety Board investigator-in-charge (IIC), two witnesses reported that on the morning of the accident, at approximately 0920, they observed the helicopter being started and lifting off the ground before moving to the run-up area, which is located at the southeast corner of runway 34-16. The witnesses stated that the helicopter then settled onto the ground facing north-northwest [320 degrees], and remained there for the next 2 minutes at takeoff RPM. The witnesses reported that the helicopter then lifted off the ground to about 3 to 4 feet before turning slightly to the right, then making a left turn of approximately 320 degrees before slowly accelerating and aligning itself parallel to the taxiway. The witnesses stated that the helicopter then slowly climbed to 75 to 100 feet above ground level (agl) before departing to the north, and at all times the helicopter sounded normal and was very smooth in flight. Numerous witnesses reported seeing the helicopter flying between 300 and 500 feet agl and heading north before experiencing an in flight breakup and impacting terrain. One witness reported hearing what he thought "…was the engine making a loud noise, like a large diesel truck roaring, then there was a large, loud bang north of my barn and some pieces fell to the ground." A second witness reported hearing the helicopter "...make a loud bang, then watched it fall from the sky." A third witness reported seeing a small helicopter flying off to his left, "...and [in] a matter of seconds I saw smoke from where the helicopter was flying. I saw the aircraft crash into the field." A fourth witness reported seeing a small helicopter flying north from AWO, "...and as it disappeared into the distance I heard a large prolonged 'shuddery boom,' and then no more helicopter engine noise." The NTSB IIC and two Federal Aviation Administration (FAA) aviation safety inspectors traveled to the accident site. The helicopter was located in an open field approximately 2 nautical miles north of AWO. There was no post crash fire. After an initial onsite examination of the aircraft and documentation of the debris field, the helicopter and all associated components were recovered and moved to a secured location at the Arlington Municipal Airport, where representatives from the NTSB and the FAA would examine the wreckage in greater detail at a later date. The helicopter, which had been purchased by the pilot-rated student three days prior to the accident, had been rebuilt by a local certificated airframe and powerplant mechanic. The mechanic personally delivered the helicopter to the pilot-rated student at approximately 1800 on November 24th. In a telephone interview with the IIC on November 28th, the mechanic reported that on November 16th and 17th, he conducted test fights of the helicopter with the assistance of another pilot. The test pilot stated in a telephone interview with the IIC that he observed no anomalies with the aircraft during the test flight. The test pilot also revealed that on November 25th, the day after the new owner purchased the helicopter, he personally flew with him for approximately 45 minutes, letting the pilot/owner take control of the aircraft during various portions of the flight. Additionally, the mechanic had a second pilot conduct a test flight on November 24th. In a written report to the IIC, the second test pilot stated that the mechanic requested that he take the helicopter up and put it into an autorotation, checking to make sure that the main rotor blades were adjusted properly. The test pilot reported taking the helicopter up to 1,000 feet, dropping the collective, and observing the rotor RPM to be low. The pilot stated, "I landed and reported my findings to [the mechanic], [who] made some adjustments. I did another flight and found the rotor RPM was now where it should be. At the time of my flight this ship had the same doors on it that I fly with (Tech-Tool doors)." The mechanic reported that the total time for all of the test flights was 4.1 hours. In a statement provided to the IIC dated November 29, 2004, the mechanic reported that the helicopter's annual inspection was completed and the aircraft was delivered to the pilot-rated student about 1800 on November 24th. The mechanic further reported that the Tech-Tool doors were properly installed and that the [door] pins were all in place. The mechanic stated that on November 24th, prior to delivering the helicopter to the pilot-rated student, "...I told him that he would have to reinstall the original factory doors before flying the helicopter, because I had not finished the weight and balance for the Tech-Tool doors." Two witnesses provided the IIC with statements relative to their personal observations during the days prior to the accident. The first witness reported that after observing the helicopter being test flown on November 24th and put back in front of its hangar, he noticed that the [door] pins were not in the doors. The witness further reported that on Friday, November 26th, he again noticed that the helicopter's [door] pins were not installed. The second witness reported that about 1100 on the day before the accident, November 26th, while in the owner's hangar looking the helicopter over, "I commented to [the owner] that the cotter pins were missing or not installed to hold the doors on." The witness stated that the owner told him he was aware of this and that there were a couple of small scratches on the left door window that he would have to remove. PERSONNEL INFORMATION The flight instructor, who occupied the left pilot seat, was a full time employee for a local emergency medical air ambulance operator. The flight instructor held a rotorcraft-helicopter airline transport pilot certificate, with commercial privileges for airplane single and multiengine land, and instrument airplane. The pilot also possessed a flight instructor certificate for airplane single-engine, rotorcraft-helicopter, and instrument airplane and helicopter. The flight instructor possessed an FAA Class 1 medical certificate dated March 16, 2004, with a limitation to wear corrective lenses. The pilot reported on his most recent airman medical application a total flying time of 8,100 flight hours, with 150 hours accumulated in the previous 6 months. The pilot-rated student, seated in the right seat, was receiving his first instructional flight in the helicopter, which he had just purchased three days prior to the accident. At the time of the accident the pilot-rated student held a private pilot certificate for single-engine land airplanes. The pilot also possessed an FAA Class I medical certificate dated March 8, 2004, with a limitation to wear lenses that correct for distant vision, and possess glasses that correct for near vision. On the application for the medical certificate, the pilot reported his total flight time was 300 hours, with 25 hours flown in the previous six months. AIRCRAFT INFORMATION The two-seat Robinson R22 Beta helicopter, serial number 1529, was issued a standard airworthiness certificate on May 7, 1991. A review of the helicopter's maintenance records revealed the most recent annual inspection was completed on November 24, 2004, with a total airframe time of 2728.3 hours. The Hobbs hour meter read 4.1 hours at the last annual inspection and 4.5 hours at the accident site. The aircraft had a Textron Lycoming O-320-B2C engine, serial number L-171189-39A. Total time on the engine at the last annual inspection was 502.1. In a statement provided to the IIC on November 28, 2004, the certificated airframe and powerplant mechanic reported that during the rebuild of the helicopter the tail rotor gearbox was sent to Robinson Helicopter Company to be repaired; total time on the gearbox was 575 hours, with a time between overhaul (TBO) of 2,200 hours. The mechanic further reported that the overrunning clutch was also sent to Robinson Helicopter Company to be repaired; total time on the clutch was 575 hours, with a TBO of 2,200 hours. The mechanic stated that the main rotor blades were timed out, with blade life being 2,200 hours; the blades had 13 to 14 hours left on them when the helicopter was sold. The mechanic reported the tail rotor blades had accumulated 832.5 hours, and, were life limited at 5,520 hours, the main rotor transmission was new with zero time, and the actuator had a total of 218 hours, with a TBO of 2,200 hours. In a subsequent conversation with the mechanic who rebuilt the helicopter, the mechanic stated to the IIC that the reason the helicopter was being rebuilt was that the pilot-rated student had requested that the mechanic rebuild the helicopter to his specifications. The mechanic stated that the rebuild did not commence until the pilot-rated student made the request; there was no repair work done to the helicopter prior to this time. METEOROLOGICAL INFORMATION At 0853, the Automated Surface Observing System (ASOS) at the Snohomish County Airport/Paine Field (PAE), located 17 nautical miles south-southwest of the accident site, reported wind 300 degrees at 9 knots, visibility 10 statute miles, light rain showers, scattered clouds at 1,700 feet, broken clouds at 2,500 feet, overcast clouds at 5,000 feet, temperature 4 degrees C, dew point 2 degrees C, and an altimeter setting of 30.12 inches of Mercury. Rain began at 29 minutes after the hour. At 0935, the AWO Automated Weather Observing System reported wind calm, visibility 10 statute miles, overcast clouds at 2,000 feet, temperature 5 degrees C, dew point missing, and an altimeter setting of 30.17 inches of Mercury. At 0953, the PAE ASOS reported wind 320 degrees at 10 knots gusting to 18 knots, 280 degrees variable to 340 degrees, visibility 10 statue miles, scattered clouds at 2,300 feet, broken clouds at 2,700 feet, overcast clouds at 3,400 feet, temperature 5 degrees C, dew point 2 degrees C, and an altimeter setting of 30.14 inches of Mercury. WRECKAGE AND IMPACT INFORMATION The helicopter came to rest in open pasture tilted on its left side at an angle of about 10 degrees, on a magnetic heading of 135 degrees. A global positioning system (GPS) revealed that the accident site was at latitude 48 degrees 11.564 minutes North and longitude 122 degrees 09.017 minutes West at an elevation of 56 feet mean sea level (msl). The debris path was oriented along a magnetic heading of 315 degrees, covering a linear distance of approximately 1,325 feet, and a lateral distance of about 800 feet. The beginning of the debris path was evidenced by various pieces of small Plexiglas, followed by larger pieces of Plexiglas in a southeast to northwest orientation. A detailed examination of the debris field revealed that the right door, which was intact and exhibited minimal damage, was located 309 feet south-southeast of the impact site. Components of the left door were found in varies locations along the debris path and prior to the main wreckage, with the left door handle located 315 feet southeast of the main wreckage. The tail rotor gearbox was located 385 feet west-southwest of the main wreckage. The gearbox assembly and the tail rotor assembly were separated from the aircraft but remained connected as one unit. The tail rotor drive shaft was separated from the tail rotor's gearbox assembly linkage and located 698 feet south-southeast of the main wreckage. Tail rotor blade #2 was found 485 feet southeast of the main wreckage, while tail rotor blade #1 was about 480 feet southeast of the main wreckage, and approximately 25 feet southwest of tail rotor blade #2. The inboard 7 inches of both tail rotor blades remained attached to their respective hub plates. The empennage assembly, comprised of the vertical and horizontal stabilizers was separated from the tail rotor gearbox assembly and located 635 feet south-southeast of the main wreckage site. Surface signatures of the component were consistent with separation in overload. The forward section of the tail cone assembly, approximately 25 inches in length, remained partially attached to the helicopter's upper frame assembly. Two additional sections of the tail cone were also found south of the main wreckage; one piece with a DANGER decal was located 715 feet southeast of the main wreckage, while a piece which displayed "29Q" was found 733 feet southeast of the main wreckage. An examination of the helicopter's driveline revealed that the drive belts were both intact and in place. Neither belt exhibited indications of rolling or twisting. The lower actuator bearing was trapped by the crushed cooling fan and earth and could not be checked for free rotation. The belt tension actuator was fractured at the upper bearing attachment point. The upper actuator bearing was free to rotate a few degrees, but was constrained by the forward flex coupling contacting the frame. The forward flex coupling was bent, but intact. The main rotor gearbox contained blue oil and was free to rotate at least one full turn of the output shaft. The mast tube appeared to be straight, but was fractured at the top of the gearbox. The mast was bent at the top of the main rotor gearbox. The droop stops for both main rotor blades were intact and in place. Mast bumping was indicated as the result of droop stop tusks and root fitting hub contact. Mast damage was also observed under the teeter stops. Main rotor blade SN 8772A was intact and exhibited trailing edge compression buckling. It was bent slightly downward in the inboard portion and upward near the tip. Streaks of a red substance were present near the leading edge of the blade, about 33 to 40 inches from the blade tip. There was also a streak of a red substance on the blade's upper surface approximately 80 inches from the blade's tip. Main rotor blade SN 8786A was fractured approximately 2 feet from the coning bolt. The aft portion of the blade had separated from the spar over a span of about 3 feet outboard from the spar separation. Streaks of a red substance were observed near the leading edge of the blade in an area from approximately 22 inches to approximately 32 inches from the blade tip. The intermediate flex coupling was detached, and the flexplate arms had separated from the tail rotor driveshaft yoke. The tail rotor driveshaft was intact, but was bent about two-thirds of the way to the aft end. The tail rotor driveshaft damper bearing was free to rotate. The tail rotor driveshaft damper assembly was separated from the bearing and the tail cone mount point. The aft flex coupling was separated; the flexplate arms had separated from the tail rotor gearbox input yoke. The flexplate arms were bent rearward. The tail rotor gearbox was free to rotate at least one full turn. The gearbox sight glass exhibited blue oil. The tail rotor slider bearing assembly was free to rotate at least one full turn. The tail rotor hub was intact. Both tail rotor blades were fractured at approximately 8 inches from the center of rotation. Tail rotor blade SN 5907D exhibited significant deformation and separation of the leading edge near the tip, as well as some yellow material transfer. Tail rotor blade SN 5927D exhibited chips in the paint near the leading edge. The cockpit/cabin area was destroyed. Cockpit documentation of the aircraft's instruments was not possible on site. The aircraft's right skid was visible lying on the right side of the aircraft imbedded
The divergence of the main rotor from its normal plane of rotation for an undetermined reason, resulting in rotor contact with the aircraft's left windscreen. The failure of the door pins to be installed was a factor.
Source: NTSB Aviation Accident Database
Aviation Accidents App
In-Depth Access to Aviation Accident Reports
