Moultrie, GA, USA
N66VJ
MAULE M-5-180C
The airplane was flown from Texas to Georgia, with an intermediate fuel stop in Mississippi. After landing at an airport in Georgia, the pilot/owner realized that his destination was situated on a different airport, located about 6 miles away. The pilot stated that he departed for the other airport, and when the airplane was at an altitude of approximately 1,500 feet above mean sea level, and 2 miles from the second airport, the engine "quit running." Attempts to restart the engine were unsuccessful, and the pilot conducted a forced landing to a field, which resulted in substantial damage to the airplane. Post-accident examination revealed that the airplane had sufficient fuel, and was configured properly for flight. The engine was successfully started and run with no problems. A detailed examination of the engine compartment revealed that the carburetor heat duct, which consisted of a material typically referred to as "scat tubing," was split around most of its circumference. Maintenance records indicated that an annual inspection was completed 4 days prior to the accident. The records indicated that the duct was installed on the airplane at least 8 years prior to the accident, and may have been installed 19 years prior to the accident. A representative of a manufacturer of aircraft scat tubing stated that the company considered the material to have a "shelf life" of 20 years.
HISTORY OF FLIGHT On April 22, 2009, about 1300 eastern daylight time, a Maule M-5-180C, N66VJ, was substantially damaged during a forced landing while on approach to Spence Airport (MUL), Moultrie, Georgia. The pilot/owner and the two passengers were not injured. The personal flight was operated under the provisions of Title 14 Code of Federal Regulations Part 91. Visual meteorological conditions prevailed for the flight, and no flight plan was filed. The pilot stated that he departed from Hilltop Lakes Airport (OTE4), Hilltop Lakes, Texas, and made an intermediate fuel stop in Mississippi. He then flew to Moultrie Municipal Airport (MGR), Moultrie, Georgia, but realized that his intended destination, the Maule factory, was located at MUL. He departed MGR for MUL, which was 6 miles to the northeast. He stated that the fuel selector was set to the "BOTH" position for the flight between MGR and MUL. The pilot applied carburetor heat and switched the fuel boost pump on for the approach and descent into MUL. When the airplane was at an altitude of approximately 1,500 feet above mean sea level (msl) and 2 miles from the airport, the engine "quit running." The pilot looked at the fuel pressure gauge, and saw that it read "0 psig." He stated that the engine "started to run a couple of times," but he recognized that he would be unable to reach the runway, and executed a forced landing in an open field. Shortly after touchdown, the right main landing gear caught on an object or irregularity in the field, and caused the right wing to strike the ground. The left wing then struck the ground, and the airplane came to rest approximately 120 feet beyond its touchdown point. PERSONNEL INFORMATION FAA records indicated that the pilot held a private pilot certificate with a single-engine land rating. The pilot reported 1,014 total hours of flight experience, with 161 hours in the accident airplane make and model. His most recent flight review was accomplished in August 2008, and his most recent FAA third-class medical certificate was issued in July 2008. AIRCRAFT INFORMATION The airplane was manufactured in 1985, and first registered to the accident pilot in February 2008. The most recent annual inspection was completed four days before the accident, on April 18, 2009. As of the date of the accident, the airplane had accumulated 1,243 total hours in service. METEOROLOGICAL INFORMATION The MGR automated weather observation 20 minutes prior to the accident included winds from 270 degrees at 10 knots, with gusts to 14 knots, clear skies, 4 miles visibility in haze, temperature 23 degrees C, dew point 6 degrees C, and an altimeter setting of 30.14 inches of mercury. The MGR automated weather observation 20 minutes after the accident, included winds from 290 degrees at 5 knots, with gusts to 14 knots, and an altimeter setting of 30.13 inches of mercury. Overlay of the temperature and dew point values on a reference chart for carburetor icing potential revealed that the ambient conditions were in the region of the chart denoted as "serious icing at glide power." ADDITIONAL INFORMATION According to the Federal Aviation Administration (FAA) inspector who responded to the accident, the fuel selector was found in the "Both Tanks" position, and the carburetor heat control was found in the "ON" position. Approximately 40 gallons of fuel were obtained when the tanks were drained in preparation to remove the wings and transport the airplane to MUL. The FAA inspector, and a certificated mechanic with airframe and powerplant ratings, and an inspection authorization, examined the airplane after it was recovered to MUL. According to the mechanic, the fuel lines and gascolator were checked for obstructions and contamination, but none was found. The fuel that was drained from the carburetor was unremarkable. The mechanic then introduced fuel to the fuel system upstream of the fuel boost pump. The boost pump was activated, and fuel pressure was obtained "right away." The engine then started normally. The engine was run to a maximum of 2,000 rpm, with "no problem." The magnetos were checked at 2,000 rpm, and no problems were noted. The airplane was equipped with a flexible duct that was routed from an exhaust system shroud to the carburetor inlet air box, and which was intended to provide warm air to the carburetor when the carburetor heat control was activated. The duct was circular in cross section, approximately 4 inches in diameter, and consisted of silicone-impregnated cloth wrapped on a spiral wire for rigidity. The duct material was typically referred to as "scat hose" or "scat tubing." Examination of the duct revealed a split that extended approximately 3/4 of the way around the duct circumference, close to the point where the duct attached to the exhaust shroud. A review of maintenance records revealed only two entries which mentioned scat tubing. An entry dated September 1990 and that listed a "Hobbs" time of 306.5 hours, explicitly stated "changed carb heat hose." An entry dated October 2001, which listed a "recording tach time" of 922.7 and a "total time in service" of 1020.76, contained the text "installed new engine scat tubing as needed," but it could not be determined whether the carburetor heat duct was replaced at that time. A representative of a manufacturer of aircraft scat tubing stated that the company considered the material to have a "shelf life" of 20 years.
A loss of engine power due to carburetor icing as a result of the maintenance technician's failure to detect and correct the condition of the carburetor heat duct.
Source: NTSB Aviation Accident Database
Aviation Accidents App
In-Depth Access to Aviation Accident Reports
