Alamogordo, NM, USA
N91137
NORTH AMERICAN NAVION
The commercial pilot stated that, while in cruise flight, the engine began to run rough and that he noted that the Nos. 1 and 5 cylinders were indicating significantly cooler temperatures than the other cylinders. About 12 minutes later, the pilot noticed an "acrid metallic smell" in the cabin. The pilot turned the airplane toward the closest airport as the engine continued to run rough and produce a "metallic clanking" sound. Unable to reach the airport, the pilot made a forced landing in a field about 100 yards short of a road. The airplane continued into a drainage culvert and came to rest on the road. A postaccident examination of the engine revealed that the engine crankcase was cracked at the base of the No. 5 cylinder and the cylinder's rocker box cover exhibited multiple holes. The oil sump contained a large amount of metal debris and damaged components from the No. 5 cylinder. The No. 5 cylinder exhaust valve spring key was worn and damaged. The exhaust valve guide was fragmented and the valve guide bore was worn beyond the specified size, which indicated the valve guide was moving inside the guide bore. The No. 5 piston and cylinder damage were a result of the valve being released into the cylinder during engine operation. It is likely that the valve spring key failed and allowed the valve to release into the cylinder.
On June 24, 2016, about 1015 mountain daylight time, a North American Aviation Navion airplane, N91137, made a forced landing near Alamogordo, New Mexico. The pilot and one passenger were not injured and the airplane sustained substantial damage. The airplane was registered to and operated by the pilot under the provisions of 14 Code of Federal Regulations Part 91 as a personal flight. Visual meteorological conditions prevailed at the time of the accident and no flight plan had been filed. The cross-country flight departed Sierra Blanca Regional Airport (SRR), Ruidoso, New Mexico, at 0938. The pilot stated that he and his passenger were flying in a planned proficiency competition with several other airplanes. The objective of the competition was to predict a time en route and total fuel consumption for a predetermined four-leg route, then fly the route as close as possible to the predicted time and fuel consumption (Figure 1). Figure 1 – Aeronautical Chart with Flight RouteThe airplane was in cruise flight and level at 7,500 ft mean sea level (msl) when the pilot noticed the engine was "running rough." At 0958, the Nos. 1 and 5 cylinders were significantly cooler than the other 4 cylinders; No. 1 cylinder head temperature (CHT) was 350° and the exhaust gas temperature (EGT) was 990° while No. 5 CHT was 305° and EGT was 1320°. In contrast, the No. 6 CHT was 398°. At 1010, the airplane reached 8,000 ft msl over mountainous terrain when they noticed an "acrid metallic smell" in the cabin. The pilot made a distress call on the radio, then a right turn towards an airport. About 13 nautical miles (nm) southeast of Alamogordo-White Sands Regional Airport (ALM), the engine was "running very rough" and the pilot heard a "metallic clanking" sound. He reduced the engine power and descended. About 5 to 6 nm from ALM, the engine continued to operate with reduced power and the airplane continued to descend. The pilot setup for an emergency landing on a residential road, but with no engine power available the airplane landed in a field about 100 yards short of the road. The airplane continued into a drainage culvert and then came to rest on the road. The airplane sustained substantial damage to the engine mounts, firewall, wing spar, fuselage, and empennage (Figure 2). Figure 2 – Airplane on RoadThe responding Federal Aviation Administration (FAA) inspector conducted a postaccident examination at the accident site with the pilot. They removed the engine cowling to examine the Continental Motors IO-520-B engine. The No. 5 cylinder appeared damaged and the engine crankcase was cracked in the same area (Figure 3). Figure 3 – Engine Cylinder No. 5 DamageA postaccident examination, conducted by the NTSB and Continental Motors, revealed that the No. 5 cylinder rocker box cover had been previously removed by the FAA inspector and was found in the engine compartment with an inner exhaust valve spring, an outer exhaust valve spring, a damaged valve guide, portions of a roto coil assembly, damaged valve spring keys, and six machine screws and lock washers. The rocker box cover contained a hole directly over the exhaust valve assembly. The engine crankcase was cracked at the base of the No. 5 cylinder, which measured about 2 inches. The No. 5 top spark plug exhibited mechanical damage. The rest of the engine's spark plugs displayed 'normal' to 'worn out normal' patterns when compared to a Champion Aviation Check-A-Plug chart. The oil filter safety wire was found attached to the fuel pump hose fitting. The oil filter was opened and contained metal debris. The oil sump was removed and contained a large amount of metal debris and damaged pieces of engine components, to include the No. 5 piston, piston rings, exhaust guide, and exhaust valve head. The No. 5 cylinder was removed and damage was observed to the cylinder head, cylinder wall, intake push rod and piston connecting rod. The rod was twisted and its pin displayed deformation on both ends. The rod bearing exhibited normal wear patterns. The No. 5 cylinder and associated components were retained and sent to Continental Motors for further examination. The No. 5 cylinder was disassembled (Figure 4) and examined at the Continental Motors Analytical Department under the auspices of the NTSB. The examination revealed that the exhaust valve guide was fragmented; some of the valve guide fragments were not recovered for examination. The valve guide was marked with "FAA-PMA" on one of the fragments, which indicated that it was not a Continental Motors part. FAA Parts Manufacturer Approval (PMA) are third-party manufactured replacement or modification parts sold for installation on a type-certificate product. The valve guide bore (Figure 5) was worn beyond the specified size and showed signs of the value guide moving in the guide bore. The exhaust valve head hardness was checked and met the appropriate specification. Only one valve key spring was found with the parts and it was worn. Figure 4 – No. 5 Cylinder Parts Disassembled Figure 5 – Cylinder Diagram A review of the airplane maintenance logbooks revealed that on January 20, 2006, at an engine total time (TT) of 358.3 hours, the No. 5 cylinder was replaced with an overhauled Engine Components International Division (ECi) cylinder. A 100-hour engine inspection was complete on March 23, 2016 at an engine TT of 1,089.9 hours. At the time of the accident the engine had accumulated 1,099 hours TT.
The failure of the No. 5 exhaust valve key spring, which resulted in a total loss of engine power.
Source: NTSB Aviation Accident Database
Aviation Accidents App
In-Depth Access to Aviation Accident Reports
